Fuel Instruments & Engineers Pvt. Ltd.
 
 
 
 

Dynamic Balancing Machine [ Model- HDCM ]

 
 
 
Dynamic Balancing Machine
Dynamic Balancing Machine HDCM
   
Dynamic Balancing Machine
Dynamic Balancing Machine
Get A Quote
Get  A Quote
Dynamic Balancing Machine HDCM
Dynamic Balancing Machine
Get A Quote
   
Machines model HDCM are belt driven horizontal type photo scanning Universal Hard Bearing Balancing Machine, provided with microprocessor based measuring panel HDCM – 8500 suitable for balancing different shapes of rotors, of electrical machines, cylinders, fly wheel, rotor of centrifugal pumps and any other type of rotating machines.
These machines are very simple in design. No drive coupling / adaptor etc. required to connect to the rotor to be balanced. It has following advantages
 
• Coast saving on manufacturing of precision adaptor to connect drive coupling to rotor.
• Any rotor can be balanced without loosing time in manufacturing of adaptor.
• The balancing accuracy of rotor not disturbed due to unbalance in drive coupling / adaptor
• Belt drive machine are more accurate (about 5 times) as compared to end drive machine.
The machines features a very simple operation. The working cycle is fully automatic. From safety point of view a double press push button starts machine, Measures and stores the unbalance values on DPMs for two Plane simultaneously and stops machine. Key board facility provided in measuring panel for correct data feeding of rotor with 1 digit accuracy for its dimensions like A.B. C, R1 & R2. Tolerance limits of both correction planes i.e. +11 & +12 can be feed so that when rotor is balanced within the limits respective LEDs glow up, indicating no further correction necessary. For other details please refer “ features of measuring panel HDCM-8500”
   
 

 

Standard Features :
 
Digital display for unbalance indication
   
 
Amount and angle for unbalance for both planes displayed on separate DPMs. Hence linear accuracy is very goos as compared to analog meter + digit for amount and + degree for angle.
   
Digital display for RPM indication
   
 
A DPM is provided to indicate balancing speed continuously as a standard feature.
   
Auto Stop
   
  No necessity to stop machine once started. It stops automatically after stabilization of unbalance results.
   
Simultaneous Indication
 
Amount and angle of unbalance in both planes displayed simultaneously and remains displayed (stored ) till next run. This totally eliminates operation of plane selector and reduces additional time for stabilization of readings in other plane.
 
Key-Board
 
Data of rotor dimensions and balancing tolerance i.e. values of A,B,C,R1,R2, t11,t12 are fed by key operation. Hence accuracy of data feeding is accurate up to 1 digit.
 
Tolerance Indicators
 
Separate LEDs are provided for both planes which glow when unbalance is reduced within balancing tolerance.
 
Auto Range
 
Depending upon whether unbalance amount is more or less a respective course or fine range gets automatically selected till rotor gets balanced within tolerance limits, Multiplier operation is totally eliminated
 
Data store
 
Data of various rotors can be stored against respective rotor type nos. Hence no need of measuring of rotor dimensions or rotor data feeding when repeat balancing operation required. Just call rotor type no. and machine is ready for balancing.
 
Self Check
 
Panel is provided with ‘self-check’ mode which checks proper functioning of digital displays, LEDs is cyclic operation. This helps immediate fault detection.
 
   
Additional Features on Demand :
   
  Printer :
   
 
A matrix printer can be connected through ‘FIE’ software. It shows runs till rotor is balanced within balancing tolerance.
   
  Component Indication :
   
 
‘FIE’ software specially developed with 3-99 component indication is suitable for balancing of rotor with fixed locations for balancing correction.
   
  Unbalance Correction :
 
   
Drill attachment 8mm capacity portable drill With supporting overhead railing.
Separate drilling attachment 19mm. Capacity with a vertical drilling head, manual.
Portable type reveting hammer (piston type) speed 1800 blows/minute, capacity 6mm in a aluminum suspected from top with rail.
Tangential belt drive, in addition to standard ( suitable for a particular type of rotor for production balancing )
Longitudinal movement of right hand pedestal by chain & sprocket attachment.
   
Technical Specifications :
   
 
"FIE" Horizontal  Hard Bearing Belt Drive Dynamic Balancing Machines.
   
 
Models
Unit
HDCM-10
HDCM-30
HDCM-50
HDCM-100
HDCM-300
Wt. of rotors
kg
0.2-10
0.3-30
0.5-50
1-100
3-300
Max. wt. on each pedestal
kg
7.5
22.5
30
75
180
Max. diameter of rotor
mm
250
500
500
800
1000
Max. distance between bearings
mm
300
1200
1200
1200
2100
Min. distance between bearings ( drive outside pedestal )
mm
20
50
50
50
150
Shaft diameter
mm
5-50
5-50
5-50
15-80
20-120
* Balancing speed range ( n )
RPM
750-3000
500-2000
500-2000
400-1600
300-1500
Power of drive motor
HP
0.33
0.75
0.75
1.5
3
Acceleration capability ( gs2n2 )
kgm2n2
0.29x106
0.37x106
0.37x106
0.88x106
3.9x106
Min. Unbalance mass measured
g
0.01
0.1
0.1
0.1
0.1
Max. Unbalance mass measured
kg
0.4
4
4
4
4
Unbalanced reduction ratio
%
95
95
95
95
95
Min. Achievable unbalance per rotor wt. ( For max. rotor wt. )
gmm / kg or micron.
0.2
0.2
0.2
0.2
0.2
 
The balancing speed depends upon selection of the rotor diameter, where drive is to be given and the motor pulley diameter.
All the machines above operate on mains supply of 400 to 440 V, 3Ø, 50 cycles.
Due to constant R & D, specifications and features are subject to change without notice. The dimensions given above are approximate.
 
 
 
 
 
 
 
Designed by : MID   Hosted by : GID   Promoted by : PBD